Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
Were you in search of critical information about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately challenging task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and also embeded in the new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will assist you install a new bath tub in your washroom if you have actually currently purchased a new bathtub and also do not need to change the arrangement of your previous water system pipes.
Your tools and material list need to consist of the following:
Getting ready for the Setup
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture fairly very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on How to Install a Bathtub Yourself. Thank you for spending some time to read through our content. Are you aware of another person who is interested by the topic? Do not hesitate to promote it. Thanks for going through it.
Book Today! Report this page